very uninpressed

[rjh12904]

I just got this put back together and I am very disappointed
I have rode stock blasters with more ass then mine
new topend with a 240 big bore
just had carb cleaned and rebuilt
new coil
I got this not running and stock everything
my problem is that it has bad power at the upper rpms
its good from idle to half throttle then it still revs but doesn't have much power
checked the reeds they are lightly gapped at ends
no air leaks sprayed everything
should I start looking into a better carb
could the very small space on reeds cause the weak upper rpms
starts good and idles good and revs good
the other issue is when wheeling? it pulls hard to left is this common I tried seeing if I can tweak the chain tensioners to correct it but didn't work

 

[super noober]

what carb and jets are you using?

 

[stephen12091985]

are you running a stock carb?and the wheeling thing make sure you have same psi in both tires,axle maybe bent,may need axle bearings

 

[2strokepower]

yes get a bigger carb.30mm-35mm

 

[rjh12904]

its stock I went up on the main but then it wouldn't rev past half past throttle

 

[super noober]

is your tors still hooked up? what size main is in it now?

 

[stephen12091985]

ur carb is deffinitely to small.get a pwk,pj 34-35mm.also what kind of exhaust do you have?

 

[blasterdude14]

guys he mentioned a small gap in the reeds thats the problem. replace the reeds if there is any sort of gap, chip, crack they need replaced.

 

[doc_speeder]

The side pull when you wheelie can be caused by a low tire, or bad bearings in the swingarm or rear axle. Or something bent etc.

 

[rjh12904]

someone is selling a trenga d slide for $95 with throttle cable is this a good deal? tors is gone

 

[stephen12091985]

someone is selling a trenga d slide for $95 with throttle cable is this a good deal? tors is gone

there like 150 new

 

[rjh12904]

is it a good carb or stay away from it

 

[stephen12091985]

i couldnt tell you i would let someone that has one tell you or someone that knows more about them.and my bad i dont know how much a trenga carb it i was refering to a keihin or oko

 

[specialized7]

try to find a PWK airstryker 35mm

 

[98 tunner]

Sounds defanitly like the carb is to small. Just about all used reeds will have a small gap between peddels and cage. The pressure in the cylinder will hold them shut, as long as they are not chiped or cracked the are fine.

 

[MXsandracer]

ur carb is deffinitely to small.get a pwk,pj 34-35mm.also what kind of exhaust do you have?

i'll second this. what exhaust are you running?

 

[tyler1blaster]

what exhaust are u runnin????????????????????!?!?!? my keihen 34mm is da bomb u should get one..... but for the wheelies one of your tires is most likely low...that or your axle isn't straight

 

[alllenlewis2]

dont get a carb get the reed be alot cheaper unless u just wanting to upgrade

 

[nofxfan125]

Reeds probably are not the problem.
Get a PJ34 or PWK35 keihin carb.
Get a decent exhaust.

You'll be happier.

You'll be even happier if you port it!

 

[98 tunner]

dont get a carb get the reed be alot cheaper unless u just wanting to upgrade

Reeds would be a waste of money for his problem. Better reeds will not work right if they can't get the air that they need. He needs a carb!!