pro honda hp2 guys

[4cfed]

. so im switching back to pro honda hp2.. iv been running klotz snowmobile techniplate at 40:1 (88 zuki lt250r) and i want to run the hp2 at 40:1 also due to jetting reasons,( dialed in right now for cold)

anyone run the pro honda hp2 at 40:1?

 

[DirtDiggler]

I run Honda Tranny Fluid , and Hondas off the trail . Thats about it. I am a Super M guy , love the low smoke properties it has . Never tried klotz , can't find it out here , I had amsoil Dominator for the shee , but shee drinks super M now too.
Good Luck Fed

 

[4cfed]

i ran nothing but pro honda hp2 for 2 years in my 01 blaster, cr125 cr250 and both my 81 and 82 250r's but always ran at 32:1.. just wondering if anyone has ran 40:1 with it... i guess it wouldnt be much to jump a main, but its very happy where its jetted at now

 

[myusername]

why dont you just run it at 32:1? not being a smart a$$, just wondering what benefits you would see just from changing your ratio that much?

 

[4cfed]

thew more oil in your premix the 'thicker' the fuel mix is so there for 32:1 would requir a jetting change... i spend time testing and tuning my jetting to get it dialed in where its at and the machine runs flawless, and i dont wanna go threw the retune process untell spring when it gets warm

 

[sheeblast]

plus 40:1 is easier to mix, half a bottle per 5 gallons. stupid reason to pick that but it works. lol

 

[4cfed]

well 4 gallons mixed 40:1 is 12.8 oz of oil, and 32:1 is 16 oz to 4 gallon.. if mixing the hp2 32:1 is simple.. pour the whole bottle in to 4 gallons or 5gallons to the bottle

 

[Blaster200boy]

I used Hp2 at 40:1, even though its meant to run at 32:1. If you mix a whole bottle of that Hp2 into 4 gallons of gas, its 32:1, if you mix the whole bottle again and use 5 gallons, thats 40:1. Just make sure you fill your gas can up at the pump or somewhere you can measure out the fuel very precise. I would pre-pay and tell them I want 4.8 gallons of gas, that way if its off a little bit, it would be rich....It smoked a bunch at 32:1, i switched to a very close 40:1 and it evened it out very nice...Hope this helps.

 

[4cfed]

I used Hp2 at 40:1, even though its meant to run at 32:1. If you mix a whole bottle of that Hp2 into 4 gallons of gas, its 32:1, if you mix the whole bottle again and use 5 gallons, thats 40:1. Just make sure you fill your gas can up at the pump or somewhere you can measure out the fuel very precise. I would pre-pay and tell them I want 4.8 gallons of gas, that way if its off a little bit, it would be rich....It smoked a bunch at 32:1, i switched to a very close 40:1 and it evened it out very nice...Hope this helps.

good info... the 32:1 is for the cr bikes since thats what its 'designed for' i dont see a problem with it since any good oil can be run at damn near any ratio you want i always do 4 gallons that way it only sits around for a week at most,
even though i run non ethanol gas i still dont let fuel sit around

 

[Blaster200boy]

good info... the 32:1 is for the cr bikes since thats what its 'designed for' i dont see a problem with it since any good oil can be run at damn near any ratio you want i always do 4 gallons that way it only sits around for a week at most,
even though i run non ethanol gas i still dont let fuel sit around

Neither do I, If I do leave it sitting though, I always throw a half can of sea foam to get rid of any moisture and it also boost octane. I always keep gas in a dark place too! letting it sit in the sun (hot or cold) decreases its octane!

 

[4cfed]

Neither do I, If I do leave it sitting though, I always throw a half can of sea foam to get rid of any moisture and it also boost octane. I always keep gas in a dark place too! letting it sit in the sun (hot or cold) decreases its octane!

my gas is stored in a garage no matter what, and i used the same can for every batch, and i messure my own with the ratio cup, my mixes are always spot on because i do the messuring every time i wont let anyone else mix my gas

 

[Blaster200boy]

my gas is stored in a garage no matter what, and i used the same can for every batch, and i messure my own with the ratio cup, my mixes are always spot on because i do the messuring every time i wont let anyone else mix my gas

Great call! I dont have to worry about my 2 strokes much, maybe 3 times a year i will mix gas for the blaster (its in arizona). The only time i mix gas is in chainsaw, weed whacker, and blower! I still use 32:1 HP2 in those little things!

 

[4cfed]

Great call! I dont have to worry about my 2 strokes much, maybe 3 times a year i will mix gas for the blaster (its in arizona). The only time i mix gas is in chainsaw, weed whacker, and blower! I still use 32:1 HP2 in those little things!

lol i used hp2 in my snowblower last winter,... and klotz this year... a winter and a half and havent had to change a plug

 

[Blaster200boy]

lol i used hp2 in my snowblower last winter,... and klotz this year... a winter and a half and havent had to change a plug

I dont ever use those small 3oz bottles ever! Its junk oil! I always use ngk plugs, hp2 oil, and 93 octane gas! and a fresh filter!

 

[2smoker85]

i use sunoco race gas in all my toys, use honda gn4 for mixing the sunoco for the blaster

 

[4cfed]

thats whats in it right now.. but i was opening and sniffin oil at work ( better smelling the better the oil) and found one that was decent so thats whats in it right now since i ran outta gas snowblowin at 930 at night

 

[4cfed]

isnt gn4 4 stroke motor oil??


gn2 is the cheaper 2 stroke oil

 

[4cfed]

back to back klotz snowmobile techniplate vs pro honda hp2 both mixed 40:1..

klotz smells better, but throttle seems to responce a little better and seat of the pants feels like it makes alittle more power and revs a bit faster

 

[sheeblast]

but which one will allow the engine to last longer?