burgard +3 a arms

S

Surfrjag

Member
Mar 18, 2010
2,760
34
85
chesapeake, va
i bought these with the intention of using them but my banshee has stolen my credit card so im not going to use them. they need balljoints for some reason these dont fit. comes with longer tie rods. civic told me ricky stator part number - rm3003 Ricky Stator if you get 4 lowers you can run the banshee spindles and save some money on a conversion as well. asking 250 shipped usps with a tracking number. thanks!!

photobucket-29071-1344544742197.jpg
 
Last edited:
Re: sms arms

thanks guys.. i got a deal on them so i figured i would pass it on. those ball joints dont fit i dont know what the guy was doing with them. thats why they need replaced. thanks civic for the info!!
 
Re: sms arms

the P.O. may have been running some other spindles/hubs/brakes...honda ???

someone jump on this sweet deal !
 
Re: sms arms

im not sure awk, they are almost 15mm on the big end and 13mm on the small. i dont know what size the honda uses but seems way to big.
 
Re: sms arms

Those are most likely VW transporter or Mazda B2000 tie rod ends which are NOT the right taper for a yamaha. I don't like reaming any ball joint mount so I wouldn't recommend reaming to get these ball joints to fit....

The Ricky Stator RS3003 in yamaha taper is the M16 x 1.50 (fine thread) ball joint in the correct taper to fit banshee spindles. The "set back" on banshee spindles is different than blaster spindles so it may require that the upper be out of its socket quite a bit more to get the camber right but they'll work.

If you wanted to run blaster spindles you could get a Frap 2419 ball joints. They may need a fancy washer to go on the front but they SHOULD also bolt into those a-arms.
 
Re: sms arms

sicivicdude said:
Those are most likely VW transporter or Mazda B2000 tie rod ends which are NOT the right taper for a yamaha. I don't like reaming any ball joint mount so I wouldn't recommend reaming to get these ball joints to fit....

The Ricky Stator RS3003 in yamaha taper is the M16 x 1.50 (fine thread) ball joint in the correct taper to fit banshee spindles. The "set back" on banshee spindles is different than blaster spindles so it may require that the upper be out of its socket quite a bit more to get the camber right but they'll work.

If you wanted to run blaster spindles you could get a Frap 2419 ball joints. They may need a fancy washer to go on the front but they SHOULD also bolt into those a-arms.
Click to expand...

blaster nerd. lol jk
 
Re: sms arms

I'm interested.....exactly what would I need to install them on an 04 with factory hydraulic disk brakes? Since the possibility of them being used with Honda spindle's.....Is it possible to buy Honda taper ball joints and use TRX250R/TRX400ex spindles, brakes, hubs and wheels? I'd rather have some to use on my 01 and be able to use Honda parts from the arms out.
 
Re: sms arms

you need those lower ball joints and the Frap 2419 ball joints for the top. i dont know what size the ball joints on there fit it was just a guess they might fit the honda's.. also you would need some extended brake lines i think. or some off another quad that are longer.
 
You must log in or register to reply here.

Similar threads

Blaster200_117
Project YSF250r is a go! A Baja built yz250 swapped blaster.
Replies
16
Views
1K
Suspension
Blaster200_117
Blaster200_117
1000rrstunna
blaster motor, AC racing bumper, Vitos oil blockoff, rear shock, alba arms, stainless lines, fenders
Replies
20
Views
3K
For Sale
iwannagofast
iwannagofast
C
leager a-arms ?
Replies
5
Views
1K
Suspension
crash
C
Blaner
Blaners Blaster awakes from slumber!
Replies
25
Views
4K
Full Rebuilds
79 bronco
79 bronco
deckpen
Modify Burgard A-Arms
Replies
14
Views
3K
Suspension
badams
badams
Top Bottom
Back