blaster

My blaster idles extremely high tellon start up. Before you just tell me to do a leak down I just did and it holds six psi for an hour with out dropping any. I had it running fine before the leak down but I am kinda new to jetting so I did a leak down test and it poured out the Reed boot. So I...

Hey guys I'm wondering how much room is there behind the hoods on the 03-06 blasters? Reason is because I got a yz250 motor in a 98 blaster and im planning on getting a newer hood, since they look real nice and ive heard they do fit, but im wondering how much room there is behind the hood...

Okay so, just rebuilt 05 blaster, .20 over piston, fresh hone, fresh seals, gaskets, you name it... rebuilt carb (new components) new reeds... TORS SYSTEM STILL HOOKED UP, ALONG WITH OIL INJECTION.. first start up, sounds okay, but will not idle at all, turn the idle screw on top of TORS system...

So I recently had my blaster rebuilt pretty much top to bottom engine wise. Got it back from the shop and it was running great. Didn’t always start on the first or second kick. Up until about a week ago it was a dozen or so or more to get running. Since it was a rebuild I pulled the plug after a...

have a 1989 yamaha blaster thats bored .2 over with a weisco piston, boyeson power reeds, stock expansion chamber, aftermarket pipe dont know the brand sticker was burnt, oil injection, aftermarket airfilter no airboxlid, currently running a 250 mainjet, needle clip is set on third in the middle...

have a 1989 yamaha blaster thats bored .2 over with a weisco piston, boyeson power reeds, stock expansion chamber, aftermarket pipe dont know the brand sticker was burnt, oil injection, aftermarket airfilter no airboxlid, currently running a 250 mainjet, needle clip is set on third in the middle...

got a 2002 blaster last night and spent all day trying to figure out why I'm losing power and not idling right I have taken the carb apart and made sure everything was good I changed the gear oil and gas I currently do not have a air box lid or a air filter cause it wasnt in when I got it I am...

Busy refurbing one of my Blasters and trying to remove the spring/coil for around 5 days now with out spending money on it. Finally used my straps for securing my Quad on a trailer and... VOILA!!! LOL Sharing is caring and a picture tells a 1000 words. Now I can paint this mofo in peace with...

im replacing the right side clutch crank seals what is the best way to go about it? do i need to crack the case? a few buddies said id need to but i havent seen anyone talking about on any of the forums i looked up. but any help and suggestions to remove and put the new ones in is greatly...

I recently was riding my blaster 200 and the bottom end locked up on me(crank bearing), so I replaced the crank, all the bearings, and seals, and the top end(piston,cylinder, rings). After doing so, I put the motor back into the quad and did the heat cycles for the break in before I put the...

I have a 1989 yamaha blaster thats bored .2 over with a weisco piston and boyeson power reeds stock expansion chamber aftermarket pipe dont know the brand sticker was burnt oil injection aftermarket airfilter no airbox lid tors unplugged i am currently running a 300 mainjet if i open it all the...

I was riding my 2002 blaster I was riding in 6th when the tires locked up the motor stopped and it came to a stop I tried to kick it over and the kick start wouldn’t budge so I kicked it as hard as I could and it turned over I kicked it 3 more times and it started right up but sounded wired so I...

So about a year ago I bought two blaster and really mainly focused on 1 but now I’m working on the 2nd one and I think some work is done on it but I’m not sure what but I took it out one day to test it and it ran great then I sprayed it with some water and slowly the rpms go away and then...

will an 89 blaster run with the tors wires unplugged or do you have to cut and cross the wires my blaster was running great untill i messed with the screw untop of the tors one day and i ended up stripping it Before it stopped running the throttle would give it little to no power barely making...

What octane gas do most of you guys run? Thanks.

My son just bought a 2002 blaster as a project. He was told that the pistons and rings were recently replaced. The headlight, kill switch, rear brake, and kick starter didn’t work. We fixed the kick starter and I should be good with the others parts. One thing that bothers me is that it...

OK, I've been looking for a while for lights for my blaster I bought this summer. Now that it's getting darker outside I need a headlight and a taillight, I don't need brakelights or anything, just a simple headlight and taillight. Does anybody know where I can buy them? Btw I'm living in...

Hello blaster community, so I was out riding yesterday and came across a hill that is notorious for being a pain in the a$$.. none of my dirt bikes were ever able to make it up due to the steep in long big rocks excessive mud etc. So I decided to try the quad on it.. it went up it like a tank...

Hello, i have a 1998 yamaha blaster yfs200. Completely rebuilt the engine because of a hole in bottom of crankcase. Im finished now and in the process of breaking it in. While out riding everything works as it should until about 30 minutes in, i lose all pressure in the clutch lever and the...

I am planning to set up my little '06 Blaster for trail riding. I have an oil block off kit, a non-tors carb with a longer throttle cable, and a reed spacer with Boysen fiber reeds. I am planning to set up the quad for trail riding so low end power is my target. I have a skidplate already...