"Nut, Flange"

tertal

Member
May 5, 2011
265
1
44
Texas
waiting for my razr's on itp's front and back to come in.. went ahead and got started with taking the old wheels off. holy crap, good thing i have a breaker bar.. those suckers were on good. some of the nuts got a little boogered up. i gathered the part number:

95707-10500-00 NUT, FLANGE | (U49)
but cant really find the exact size/thread..

has anyone tried using something from the local hardware store, preferably home depot since i work there ;)
 
I got like 12 of my lug nuts from the hardware store. If you work there, why wouldn't you take one of the ones you took off into work and match it up.

Just in case that's not an option, I believe the lug nuts are M10 x 1.25
 
I'll have to go check it out on my lunch break, I'm an expeditor so I don't see much of the sales floor during my work hours (I hide from customers hehe). Anywho thanks for the size, I just rather have an idea before I go looking at all of them.
 
Anytime I've been in HD seems like everyone is hiding from the customers ,JK. Be sur to get some flat washers so the nuts don't booger the wheels. Don't know about the Depot, but at Tractor supply they have Stainless steel washers in jobber pkgs in SAE that are pretty sweet. Always seems that most flat washers are such a poor fit.
 
Haha yea we all tend to unless your a contractor lol. But go figure my store doesn't carry 10m-1.25 flanged in stainless.. I'm assuming a stainless washer and an unflanged nut could also work?
 
Ya, I think washers would be good Idea even with flange nuts. I wasn't talking SS nut, that might be real hard to find, plus have use anti-seize on threads to prevent galling between the two steels. Hell I don't think I've been able to find flanged nuts or bolts anywhere.
 
i called ace and they have a ton of m10-1.25 in zinc flanged too! ...Isnt that what the stock ones are? mine are so old and boogered i cant tell :(
 
i called ace and they have a ton of m10-1.25 in zinc flanged too! ...Isnt that what the stock ones are? mine are so old and boogered i cant tell :(

ACE does have just about every nut and bolt made but they are expensive. I was able to goes to Lowes and they had the nuts and i used washer behind them they wernt flanged but were cheaper than ACE. i nknow lowes is a competetor but hey, they always have what i need...
 
oh home depot has the non-flanged in zinc or ss. ace has ss and zinc flanged but freaking $1 a pop! think im just going stainless washer and zinc nut, unless a ss nut is ok on the bolt? ..dont want to mess up the threading.. also need to factor in the new ITP whiles i should be getting today if UPS is nice :)
 
I run non flanged nuts regular steel M8 and have no issues at all yes i put a washer behind them and use blue locktight! I wanna say it was $8 something for all 16 and washers!
 
You do realize that a quad takes 16 nuts.... If you had to replace each and everyone, you'd only be out $16 plus tax...

How much did you pay for your ITP wheels?

yea i do realize there's 16 :p but i only boogered up the rear, fronts were ok (i guess i applied the correct amount of PB blast to the front LOL).

as for the ITP's, this is what i got;

Maxxis Razr MX ATV Tire 18x10-8 (2)
4/100 3/100 ITP Steel Wheel 8X8.5 3.5 + 5.0 (2)
for $180.96 mounted.

anywho check my build thread i'm about to start for pictures