Brand new to blasters and already huge prob

[bunch&bonadio]

Hey everyone. so i just bought a couple of blasters only one runs(barely). it'll idle but as soon as you even tap the throttle it bogs out and dies. no clue where to start. it seems like it's got compression but i can't test that. it gets gas but almost too fast. it flows out the overflow like niagra. got no clue where to start.

help? it'll idle.. hell i rode it around a tad just b4 i bought it and now it dies on me as soon as i tap the throttle it bogs out.

 

[slickerthanyou]

Float adjustment first thing! Then do some plug chops. can't hurt to do a leak test on it also!

 

[quadsrus1]

Hey everyone. so i just bought a couple of blasters only one runs(barely). it'll idle but as soon as you even tap the throttle it bogs out and dies. no clue where to start. it seems like it's got compression but i can't test that. it gets gas but almost too fast. it flows out the overflow like niagra. got no clue where to start.

help? it'll idle.. hell i rode it around a tad just b4 i bought it and now it dies on me as soon as i tap the throttle it bogs out.

Start by taking the carb apart and cleaning it out really good all the jets and everything also while the carb is apart check to make sure the float height is right if its not adjust it thats where i would start

 

[quadsrus1]

Float adjustment first thing! Then do some plug chops. can't hurt to do a leak test on it also!

Hey at least we are heading in the same direction haha

 

[slickerthanyou]

here is a how to-

here is how to make one or i sell them-
http://www.blasterforum.com/do-yourself-20/build-use-leakdown-tester-10663/

 

[slickerthanyou]

Hey at least we are heading in the same direction haha

FO sho!!!!!!!!!!!!!!

 

[Awk08]

fresh fuel ????
mix or oil injection still functioning ???
new plug ??? NGK b8es
good strong spark ???

T.O.R.S. deleted ???....................
http://www.blasterforum.com/do-yourself-20/how-remove-your-tors-655/

airleaks ?????................
http://www.blasterforum.com/do-yourself-20/videos-how-perform-air-leakdown-test-31464/

http://www.blasterforum.com/do-yourself-20/build-use-leakdown-tester-10663/


fuel overflowing points to float problems, pull, completly disassemble carb and clean all jets and orifices
pay special attention to the float valve and needle, check the rubber tip for tears,
check float height adjustment, which is 20-21.5mm from where the gasket would sit, to top of float
measured like this........................

 

[quadsrus1]

fresh fuel ????
mix or oil injection still functioning ???
new plug ??? NGK b8es
good strong spark ???

T.O.R.S. deleted ???....................
http://www.blasterforum.com/do-yourself-20/how-remove-your-tors-655/

airleaks ?????................
http://www.blasterforum.com/do-yourself-20/videos-how-perform-air-leakdown-test-31464/

http://www.blasterforum.com/do-yourself-20/build-use-leakdown-tester-10663/


fuel overflowing points to float problems, pull, completly disassemble carb and clean all jets and orifices
pay special attention to the float valve and needle, check the rubber tip for tears,
check float height adjustment, which is 20-21.5mm from where the gasket would sit, to top of float
measured like this........................

Good picture for the possible problem

 

[bunch&bonadio]

fresh fuel ????
mix or oil injection still functioning ???
new plug ??? NGK b8es
good strong spark ???

T.O.R.S. deleted ???....................
http://www.blasterforum.com/do-yourself-20/how-remove-your-tors-655/

airleaks ?????................
http://www.blasterforum.com/do-yourself-20/videos-how-perform-air-leakdown-test-31464/

http://www.blasterforum.com/do-yourself-20/build-use-leakdown-tester-10663/


fuel overflowing points to float problems, pull, completly disassemble carb and clean all jets and orifices
pay special attention to the float valve and needle, check the rubber tip for tears,
check float height adjustment, which is 20-21.5mm from where the gasket would sit, to top of float
measured like this........................

YES TO fresh fuel and new spark plug. i'm mixing myself 32:1. i removed the oil tank. should i take out the tors?

 

[L.T.]

JUST A ROCK IN THE BUSH

check your park brake wiring

 

[Awk08]

yes, delete the T.O.R.S
and if 03+ remove the park brake sensor also

 

[Jammies]

I completely X2 that it's TORS or Parking Brake. Follow your parking brake wire all the way to the back of the quad, by the read tires, and pull the end of it back. On my Blaster, if I engage the parking brake but then take it off, it won't disengage. That's how I turn it off.

 

[Awk08]

most just unplug the park brake sensor at the clutch lever (03+)

 

[PikledBeats]

most just unplug the park brake sensor at the clutch lever (03+)

Second this on 03+ just disconnect the park brake sensor ... do not cut the wires.

This sounds exactly like a TORS problem if in fact yours is 03+

For TORS 03+ use this link the other link is for 88-02 http://www.blasterforum.com/do-yourself-20/03-06-tors-removal-diy-41973/

 

[piezzi]

If the fuel is pouring out the overflow tube then the float is stuck open. Take the handle of a screw driver and tap on the outside of the carb bowl. This will usually free up the floats.