open read help

[tcoop474]

o ight well as long as its not like if i dnt have it im screwed were ok it wasnt on there when i got it and it ran so i guess me not havin that is fine

 

[tcoop474]

any ideas what those wires r

 

[tcoop474]

should i go do what blackbasterd told me to do on page one real quik?

 

[PureXTC]

Sorry I cant tell what those wires are until I take a look at my blaster. Which is across town in storage ATM

 

[tcoop474]

i just tried putting gas in the spark plug hole nothing still didnt crank so is it a electrical problem

 

[PureXTC]

You said you are getting spark correct?

 

[PureXTC]

Try plugging those holes in your carb and kick it. Hopefully you didnt put too much gas in the spark plug hole.

edit: do this... remove spark plug. kick it a few times to get that extra gas out of there. Replace plug. Plug those holes in your carb. Try starting it.

 

[tcoop474]

i just put like 5 drops in it we checked for spark again its good we have the holes plugged it still wont crank dad says it has to b a fuel problem but we just have pin pointed the problem yet. what happens if u put to much???

 

[jeepinncreepin]

when this happened to me i put gas in my spark plug hole it had spark wouldnt start the culprit base gasket spray something around it see if it spits air out mine did

 

[tcoop474]

thanx i fig it out busted reeds two of them were messed up thanx. with the mods on my quad whats the best reeds v force boysen ?????

 

[2strokenitfast]

yea i think their TORS

 

[BlasterAzores]

first: ill tell u what happened i was riding third gear powerband it bogged so i pulled in the clutch and it dies i spend bout 20 mins kicking and nothing happens

second: i get home check spark plug its a brownish red color i replace it with a new one still wont crank i pulled the spark plug back out stuck it to the frame kicked not a great spark but it sparked.

third: i fig gas problem so as most of u know by now ive only had the blaster almost 2 weeks. so i take the carb off there is hole with threads all on this thing the carbs clean but wtf is up if i had a camera i could show yall but theres just holes where something is supposed to go. the adjuster screw is there. the holes dnt leak gas or anything but they do suck in air but they have threads so they have to of had something in them. so put the carb back on and flood it gas runs threw fine. after a few i try to crank it again still nothing.

then: i looked under the hood there r wires cut just hanging theres about 5 or 6 wires cut just hanging there i know two of then are my lights i took off but the other ones i have no idea.

honestly i just wont to get this running i havent rode in about three weeks and im starting to get quite pissed at this blaster. hopefully i gave enough details yall can help me. also it does have compression.

one more thing: when i try to crank itll backfire every now and then so plz help me :-/

Have you checked the reeds?

Cant be the wires, those were already cuted before it dies on you right ?

 

[JabsBlaster88]

tcoop474

When it backfires is it going through the pipe? or coming back through the air filter? have a buddy kick it over and watch where it is coming from.

i had almost the same problem, backfire every 3rd-5th kick, i couldn't figure it out until i pulled the head off and found my piston destroyed.

[/URL][/IMG]

Also when you pulled the plug did it look like it had touched oil? just a drip or 2?

hit the forum back

 

[tcoop474]

yea im currently working on it my pistons gone that 50:1 premix the idiot b4 me was running fried it thanks

 

[JabsBlaster88]

remember to have it honed will save you the aggrivation of popping the next one

 

[tcoop474]

yea the piston aint scratched kinda scuffed but the rings seized so im going to hone it then ill put new rings n and put it back together

 

[ruthless_one3k]

I would go ahead and get a new piston while you have it out. It probably needs replaced anyway. If you still cant get it to start after you get new reeds then try checking the woodruff key on the flywheel. if it shears and the flywheel slips then that can cause backfires.

 

[06kid]

I would go ahead and get a new piston while you have it out. It probably needs replaced anyway. If you still cant get it to start after you get new reeds then try checking the woodruff key on the flywheel. if it shears and the flywheel slips then that can cause backfires.

Yeah this happened to me a couple of times with my old blaster X(

 

[tcoop474]

ill check it while ive got everything takin apart it had no compression had 30 psi after like 20 kicks and thats when i noticed reeds where gone and the rings had siezed we r gonna try to hone it and just rings and if it still dont run im prolly just gonna buy the 240 kit ive ben thinking about it