Non-running Blaster engines, stock carb, and electronics (located: in Eastern Pa zip 17901)

[phive70]

I have two dirty Blaster engines for sale right now; neither run; neither are locked up;

I can ship the small stuff, but not the engines. I'm located in eastern Pa, zip is 17901 (Pottsville, Pa). I travel to southern Delaware usually on the weekends.

One is mostly complete: It is on a 67.50 piston; Missing rings on piston. No rust in cylinder. $200

Other is mostly apart: it is on a 66.50 piston (rough looking); missing 1 side cover and clutch; I have 2 cylinder jugs, one of them maybe for this, both have rust inside. $100

1 chassis harnesses: 2xj-82590-00 (all ends are present); include CDI; $30 shipped (US) for -02 harness


1 stock carb with TORs. Sold

1 Wiseco/LA SLeeve w876ps 72mm piston (NOS), partial kit. Everything minus the needle bearing. $125 shipped (US)

VF3 reeds and cage (used). $70 shipped (US).

TM Designworks blockoff kit; $20 shipped (US)

1985 YZ250 with Clarke Tank, aftermarket exhaust, no title, complete but not running. With new Wiseco 68mm STD piston

Steel YFZ450 frame. No subframe. With skid plate.

Yes I have some of these listed on eeh-bay. Contact me on here for forum prices.

Also, to anyone interested, I'm trying to cut down on my inventory of Yamaha Blaster chassis and parts. If anyone is interested in purchasing it all, please get in contact with me. I have more than whats posted here.

 

[phive70]

I also have a NOS Wiseco 66mm piston that isn't complete, missing rings and clips. I'll include this free of charge if you buy the 72mm piston above. Maybe you can use the bearing in the 72mm?

Roundhouse rear swingarm:
I don't know anything about the swingarm. I'll get measurements later. It definitely can use some beefing up all over. $80 shipped.

NOS Vito's +3mm stroker crank kit: sold

CCP 300EX steering stablizer: Sold

+3 240 Stroker KOR ported, pump gas, less than 15hrs on it: $850

Stock Blaster engine, original, with aftermarket clutch, low hours $650.

 

[JustCallMeAnt]

I am looking for a inner clutch hub, stator cover, and kick start lever if you have any of those available for sale.

 

[Noxtol]

Do you have a blaster flywheel?

 

[phive70]

I might, I'd have to check my parts totes.

I have a 2003 Blue Blaster for sale. $450
No engine. Chassis electrical is there. ASV levers (both clutch and brakes). Pro Circuit fatty and silencer. No clutch cable or parking brake (blocked off), otherwise hydraulic system is intact. No title. No swingarm Bolt either. I may have a headlight. Good tread on all 4 tires. Located in Pottsville PA 17901. I can truck it down to southern Delaware as I'm there on the weekends.

 

[phive70]

Do you have a blaster flywheel?

I am looking for a inner clutch hub, stator cover, and kick start lever if you have any of those available for sale.

I do not have a separate fly wheel, inner clutch hub, or kick start lever. I do have a stator cover that is cracked near the sprocket guard (no gasket).

 

[lokifalkor]

Do you have a spare clutch basket that is salvageable? need the outer portion - don't care if it needs to be filed a little.

 

[Noxtol]

Have a rear grab bar by any chance?

 

[87hurricane]

Do you still have any of this stuff? I might be interested in a decent amount of it. I am new, can't PM yet I guess...

 

[Joe magazzeni]

Any frames with titles?

 

[Slydog]

Any frames with titles?

It's an old thread. I dont know id you will get a reply

 

[DaN-tHe-MaN13]

Any bare crank cases ?

 

[300iFordguy]

Realize this is an old thread but you never know. If you still have that kor ported stroked 240 I’m very interested

 

[Taco]

Looking for a clutch boss spring out of 1 if those engines if you got it.

 

[Inked soul]

I have two dirty Blaster engines for sale right now; neither run; neither are locked up;

I can ship the small stuff, but not the engines. I'm located in eastern Pa, zip is 17901 (Pottsville, Pa). I travel to southern Delaware usually on the weekends.

One is mostly complete: It is on a 67.50 piston; Missing rings on piston. No rust in cylinder. $200

Other is mostly apart: it is on a 66.50 piston (rough looking); missing 1 side cover and clutch; I have 2 cylinder jugs, one of them maybe for this, both have rust inside. $100

1 chassis harnesses: 2xj-82590-00 (all ends are present); include CDI; $30 shipped (US) for -02 harness


1 stock carb with TORs. Sold

1 Wiseco/LA SLeeve w876ps 72mm piston (NOS), partial kit. Everything minus the needle bearing. $125 shipped (US)

VF3 reeds and cage (used). $70 shipped (US).

TM Designworks blockoff kit; $20 shipped (US)

1985 YZ250 with Clarke Tank, aftermarket exhaust, no title, complete but not running. With new Wiseco 68mm STD piston

Steel YFZ450 frame. No subframe. With skid plate.

Yes I have some of these listed on eeh-bay. Contact me on here for forum prices.

Also, to anyone interested, I'm trying to cut down on my inventory of Yamaha Blaster chassis and parts. If anyone is interested in purchasing it all, please get in contact with me. I have more than whats posted here.

Do u still have the blaster motors for sale?

 

[Jeffrey Jacobs]

Do you still have the cases ? I live in Denton MD. Can travel, cash on hand.