im in northeast texas, about 20 miles south of texarkana. i hunt around lake wright patman, caddo, lake o the pines and a few places in louisiana and arkansas
My new project !!
- Thread starter 3 Wh33l3r Rid3r
- Start date
im in northeast texas, about 20 miles south of texarkana. i hunt around lake wright patman, caddo, lake o the pines and a few places in louisiana and arkansas
they are horrible around here. they are good for nothing all they do is tear sh*t up.
sh*t, imma have to make a duck huntin trip with ya 3 wheeler. I only live like 4 hours from you dude. Im from the waco area. Going to school there at TSTC. I aint never been duck huntin but have wanted to go pretty bad. Plus it'll give me a reason to run a few boxes of shells through the old 12 gauge.
well come on....early teal season starts in mid september and goes for 2 weeks and big duck season starts the first weekend in november and runs thru january...lemme know when you can make it and ill try and get you on some I:I
i been trying awk, its hard to break the mig habit of being close. its wierd the wire never touches the metal it sprays in. when i try to keep the 3/4 stick out that everybody recommends i cant even get it to weld sometimes, it burns all the way at the tip and will melt a tip in a split second. got a few people to call tomorrow and ask a few questions.
got a little more done today.....got the front rake pulled together and tacked all the way up, one of the rear supports and got the 20 degree angle cut for the transom. hopefully by the weekend ill have the transom all the way in where i can start on the runners and floor supports.
i also swapped to 4032 wire and it welds soooo much better. not quite as strong as 5036 but the welds are much better
i also swapped to 4032 wire and it welds soooo much better. not quite as strong as 5036 but the welds are much better
THANKS!! im ready to be done already.
this is a little video of the motor im gonna be running. been on a 4 week wait for the motor and once i get it it will go straight to setx performance to get some upgrades. should be a runner with mods im going with
mods
1:1.5 Ratio Roller Rockers
42mm mikuni carb
Single Cross Over Stainless Exhaust
Custom Push Rods for Roller Rockers
Valve Spring Spacers
Head Decking and Porting
Performance High Lift/Duration Cam
Performance Custom Pistons
High RPM Stroker Rods
Gator-Tail Outboards - The Original Belt Driven Surface Drive Mudmotor
this is a little video of the motor im gonna be running. been on a 4 week wait for the motor and once i get it it will go straight to setx performance to get some upgrades. should be a runner with mods im going with
mods
1:1.5 Ratio Roller Rockers
42mm mikuni carb
Single Cross Over Stainless Exhaust
Custom Push Rods for Roller Rockers
Valve Spring Spacers
Head Decking and Porting
Performance High Lift/Duration Cam
Performance Custom Pistons
High RPM Stroker Rods
Gator-Tail Outboards - The Original Belt Driven Surface Drive Mudmotor
got a little more done today..got the transom cut out and mostly welded in and im starting to fit the channel in to reinforce the transom. i also started on 1 of the runners but havent started welding em in yet.
got a little more done today...ran out of 2x4 channel to finish up the bracing for the huntdeck. but i got the main motor mounts done and covered em up with another piece of 3/16 and got one of the cross braces in....im gonna try and pick up the rest of the material this week to fish up the bracing and the floor runners.
not too bad for my first time welding aluminum
not too bad for my first time welding aluminum
Similar threads
