Boomers new parts :D

[luk3x3]

Lol, well title says it all, i splurged because i dont like the look of the stock handle bars on the blaster. so heres some pics of what i got.

Fly Handlebars red
Acerbis hand guards - red
Tusk ball joint ends (i needed them)
Tusk tie rods (needed these too)

Although i dont have a picture of the tie rods, heres pics of everything else

 

[blasterBruce]

Nice , New Stuff is always Nice !!

 

[Quadrider10]

i would return those bars. i ordered them for the blasty, and if u got the yamaha bend ones, they are way tooo low, and also they scratch really really easy!

but otherwise aewsome stuff!!

 

[luk3x3]

i would return those bars. i ordered them for the blasty, and if u got the yamaha bend ones, they are way tooo low, and also they scratch really really easy!

but otherwise aewsome stuff!!

which bend is correctly? lol. i dont remember which one i clicked. i know i read osmewhere, something about the bends.

 

[Quadrider10]

which bend is correctly? lol. i dont remember which one i clicked. i know i read osmewhere, something about the bends.

i bought the msr ones off rockey.i got atv high bend, and those are REALLY nice! lol love them!

 

[slickerthanyou]

which bend is correctly? lol. i dont remember which one i clicked. i know i read osmewhere, something about the bends.

I got some pro tapers for my sons quad mid bend they were perfect. If your tall 6' or better most any bend will work, shorter guys like a taller 14-15 degree bars.

 

[luk3x3]

i bought the msr ones off rockey.i got atv high bend, and those are REALLY nice! lol love them!

see imo, i hate high bends, reminds me to much of bikes. but i dont like the really low bends without that middle bar.

eh either way, it gives me an excuse to make them work.

 

[Quadrider10]

see imo, i hate high bends, reminds me to much of bikes. but i dont like the really low bends without that middle bar.

eh either way, it gives me an excuse to make them work.

see for me, they felt like a street bike sitting down, and when i stood up, they felt like im standing up on a street bike. lol. my arms were complety stright, and my back was bent just to reach them. i would never be able to jump my quad lik r that lol

but hey if they feel comfortable, go for it. (BTW i have an extended steering stem, and they were still too short).

 

[Xero]

My ranthals look just the same as them, after a while riding it started to hurt my back BUT i do suffer from bad back anyway...

But since on pre'small they help ALOT with cornering since their lower down i clean lean further holding onto the bars! and also gives me more room to pull for wheelies

Nice stuff!

 

[luk3x3]

and a little home tip i have, well for myself ahahaha, for riding bmx bikes, i always used those huge circular grips. well, these fit the bars perfectly, blaze orange bmx grips that were on my mosh. haha. Plus i got some extra bar clips for them to do that homemade rising kit...as far as bending over goes, im standing at 5'11. and stock height just dont feel right to me.

 

[89blaster89]

and a little home tip i have, well for myself ahahaha, for riding bmx bikes, i always used those huge circular grips. well, these fit the bars perfectly, blaze orange bmx grips that were on my mosh. haha. Plus i got some extra bar clips for them to do that homemade rising kit...as far as bending over goes, im standing at 5'11. and stock height just dont feel right to me.

nice parts you got there, i think if your not hard on your blasty those bars will be fine...and you BMX??