clutch

Hey Guys fairly new to working on these blasters and recently picked up a few. I am having a problem with the clutch not engaging. The pressure plate only moves less then a quarter inch. like its not getting pushed far enough out, ball bearing is there and seems to be fine. When i first got it...

So I recently redid the bearings and seals in my blaster engine and when I put it back together I went to test the clutch and it stays engaged and the bike acts like it is in neutral in all the gears. Also the clutch lever pulls the clutch arm but has no resistance and lever bearly retracts...

Hi Everyone, I'm replacing the clutch in my '02 Blaster and I'm wondering what methods you folks recommend for removing old pieces of gasket that are sticking to the case? I carefully took a razor blade to it with some success, but I don't want to risk damaging the metal. Any solvents I should...

I just installed my new EBC clutch and rotated the steel plates every 2 groves, does that seem correct? When I pull the clutch lever, it moves 7-10 mm before you start to feel the tension of the clutch engaging. The clutch pressure plate moves 2-3 mm out, is that the distance it should move...

I just bought my first atv, a 2003 blaster, and the previous owner told me the clutch needs to be replaced because it slips and I shouldn't ride it till I fix the clutch. How can I verify that I need to replace the clutch due to it slipping? If I need to replace the clutch, what brand would be...

Hello, I have a 1999 Yamaha blaster that just received a new top and bottom rebuild. New piston, cylinder head, crankshaft, bearings, transmission, clutches/basket, and new gaskets/jettings for the carb.Everything is jetted correctly and put back together, it has new transmission oil. A buddy...

So I bought a blaster from a buddy first drive I had it out started making this awful screeching noise which I thought was the clutch. I took the clutch cover off an removed the clutch turns out I think it's a bearing in the transmission that is spun cause whenever I spin the wheel the...

My clutch plates were stuck together so I took everything off and cleaned the plates and put them back on. Everything was back to normal the first night right after I put everything back together. Now when I let my clutch ALL THE WAY OUT my engine starts skipping and jerking the quad. Basically...

ball bearing is in there but i have the clutch boss and the pish rod and lock nut and the larger nut and the small washer that fits in the inside indentation but i cannot figure out the order they go on every way i try it the clutch wont adjust i bought a clutch kit off ebay and i think all the...

My 1999 blaster runs good other than a weird noise coming from the engine and first gear being very low. I am very concerned about the noise though. Could someone tell me what it might be? I will make a link to the video of it running.

Hello! My name is Dan, I'm from Northeastern Pennsylvania and I recently acquired an almost immaculate 1991 Blaster WITH A TITLE. This has no aftermarket parts and even has the original tires from 1991 (three digit DOT code vs. a four digit DOT code). I've wanted a Blaster since I was about...

Hello, This is my first time posting here. I've tried to find information on this subject here on the forums, the service manual, and a couple friends. Maybe I'm just blind, but I couldn't find it. The problem is the clutch doesn't seem to be engaging when I squeeze the lever (I made sure it's...

im sure there is a thread like this somewhere but I couldn’t find one. I just put in new clutch plates, cable and perch/ lever. I bought this blaster used and rebuilt the whole motor so I haven’t actually rode it yet, but it starts.. everytime I put everything back together it works fine in...

im replacing the right side clutch crank seals what is the best way to go about it? do i need to crack the case? a few buddies said id need to but i havent seen anyone talking about on any of the forums i looked up. but any help and suggestions to remove and put the new ones in is greatly...

i have a 1989 blaster the clutch stopped working a day ago the bike runs fine starts up first or second kick but when i pull in the clutch it makes an awful noise and wont engage all the way and pops as soon as you release it making it impossible to get out of first to ride the bike Any ideas to...

I recently rebuilt my 1989 Blaster and when I was going to reassemble/ adjust the clutch i have run into an issue. I have adjusted the clutch like the manual says and lined the arm up to the mark on the case, if I push the bike without the clutch it wont roll, and than I use the clutch and it...

Hello, i have a 1998 yamaha blaster yfs200. Completely rebuilt the engine because of a hole in bottom of crankcase. Im finished now and in the process of breaking it in. While out riding everything works as it should until about 30 minutes in, i lose all pressure in the clutch lever and the...

So I just got a 2000 Warrior 350 and what I’ve noticed is that it likes creeping forward with the clutch in, even after stopping with the breaks it will creep more. It is very hard to find neutral with it running too In order to shift to reverse I have to shut it off to find neutral, and then...

So today when riding my 93 blaster it was going good all morning, while riding back I had to turn sharp and slipped on mud and sent it into a donut, it was in to high of a gear so it stalled, no biggie. I started it back up and when I went to shift it back in to first, it never stopped, it kept...