Sprocket Hub STUCK!!

[specialized7]

Ok guys so i was gettin ready to rip apart my axle carrier to change bearings and put in the banshee axle and HOLY f*ck is this thing a biotch.
The 2" axle nuts were a pain in the ass but got them off.
Now im at the sprocket hub, apparently its supposed to slide off but its not its damn near welded on there, any ideas?
im not worried about anything but the sprocket hub and the carrier so pounding on the axle is ok but it just wont budge?

 

[specialized7]

i also soaked it in Penetrating oil, Would a torch help?

 

[4cfed]

pb blaster... and heat nuff said close thread!!

 

[4cfed]

i also soaked it in Penetrating oil, Would a torch help?

heat it and beat it.... sounds bad... but... take the torch and a hammer.. and it will all come together.. err uhh apart

 

[specialized7]

just heat the sh*t out of it you say? then smack it all apart?

 

[specialized7]

cuz fed its really pissing me off, i was ready to buy a new carrier and sprocket hub

 

[Blasterb0y794]

Heat, PB blaster, and a rubber mallet. If it doesnt budge, take a sludge hammer to it. If you mess it up, ill send you a sprocket hub and sprocket for free. Just pay shipping!

 

[specialized7]

alright boys ill report back tomorrow after work
Thanks for the offer blaster boy i might just have to take ya up on it

 

[4cfed]

yes.. spao kin pb blaster over night if you can.. than heat it.. try to heat it and pound it apart

 

[Blasterb0y794]

alright boys ill report back tomorrow after work
Thanks for the offer blaster boy i might just have to take ya up on it

No problem man. Its here if you need it. Its a little greasy and dirty but its nothing that cant be used. Just LMK if you need it! I:I

 

[NEONNIGHT34609]

i always heat and cool with pb blaster doing this will pull the blaster in. do it a few times it should work. dont use a BFH unless all else fails

 

[specialized7]

Should i be concentrating my heat on the Sprocket hub itself or the axle splines?

 

[brandoz28]

the sprocket hub itself, you need it to expand around the axle

 

[specialized7]

Alright Well no luck, i Started of small, a little heat and a rubber mallet nothing.
So i heated it up a little longer and smacked it somemore. still nothing.
so i heated the hell out of it and busted out the BFH and this is what it looks like now

So blasterboy message me your Paypal address and ill pay ya to ship that hub out priority.
Also anyone got a axle carrier because im gonna throw this whole rear end in the garbage

 

[Busted Warrior]

Sawzall a slit in it and then spray some pb plaster in it. That should break it loose.

 

[specialized7]

Shes already in the garbage lol i gave up with that thing it pissed me off

 

[Blasterb0y794]

DAMN!!! Doesnt the sprocket hub come off the other way though?

 

[darealblaster]

lmao you got owned pretty bad by that sprocket hub, and i thought stripped screws f*cked up my life.....that thing MUST be welded, almost like my oil drain screw, had to take a chisel to it, and even like that i spent like an hour hitting that biotch

 

[specialized7]

haha ya i was gettin mad, i had bent one and then i was liek f*ck this thing and just started wackin on it.
im gonna bring my grinder home from work tomorrow and try to cut that thing off just to salvage the carrier.
And blaster boy, i sure hope i wasent pounding it the wrong way lol?

 

[Blasterb0y794]

haha ya i was gettin mad, i had bent one and then i was liek f**ck this thing and just started wackin on it.
im gonna bring my grinder home from work tomorrow and try to cut that thing off just to salvage the carrier.
And blaster boy, i sure hope i wasent pounding it the wrong way lol?

Well what kind of axle is that? Correct me if im wrong, its been a while with a blaster, but should the axle first slide out of the carrier and then the sprocket hub come off reversed of what you were beating the sh*t out of? :-/