My highschool graduation

[Corey]

So pretty much at my school we have this thing called a Culminating project that seniors do (12th graders) I for one am one of them. After much debating on either lifting my jeep 3.5" and putting 31" tires on it and modding the living sh*t out of my automatic wheelie machine (my blaster), I decided on my blaster! This all should run me if I'm lucky under $2,000 (this list does not include anything minor that I plan on doing such as brake changes, etc. you get the picture)

My plans for my senior project is as followed (keep in mind this is in order for me to graduate high school):
-Vito's 240 big bore kit
-FMF SST pipe with TurbineCore 2 Silencer
-+4" Extended swing arm
-Larger carb
-8 paddle haulers
-Block off and Remove my oil injection
-Banshee hubs
-Sand frame
-Prime frame
-Rattle can frame silver
-Remove airbox (DONE)
-Put on a k&n air filter (DONE)
-Re-jet properly (DONE)
-Custom fabricate air flow shrouds (DONE)

Any advice + tips will be greatly appreciated and very helpful, thanks a ton!

-Corey

 

[TheWalkingPlague]

dont get fmf pipe if you are getting a 240 kit and you will want port and polishing done on it also

 

[Corey]

Why not the FMF? And yeah I forgot to add port and polish.

 

[tjsdaname]

FMF pipes are junk with a capital UNK......

 

[Corey]

FMF pipes are junk with a capital UNK......

Care to explain why?

 

[stephen12091985]

you will be better off with an f7,dyno port,lrd ect

 

[Corey]

Yeah but see, I ride in the dunes only, so I NEED something that can be spark arrested, and when I called PB, they said they discontinued the LRD.

 

[stephen12091985]

you can get them on ebay

 

[b_russell_82]

Like was said... FMF pipes are not really any good for a modded Blaster. FMF makes some good 2 stroke pipes JUST NOT FOR THE BLASTER... I would go with a Power Pros pipe, and be sure to get that 240 kit ported. If you are not going to spend the money to port it then dont get it. You might want to get intouch with one of the builders on here and see what kind of package deal you can work out with one.

 

[liljatownboy]

get a matt shearer than or fat bastard

 

[Corey]

Probably but none of them are spark arrested nor can be spark arrested which causes a huge problem to my riding. Every place I've been so far you NEED to have your bike be spark arrested. Also it NEEDS to be UNDER 97DB.

 

[sc0r1a]

holy sh*t i would love for this to have been my senior project where the heck do you go to school? are you being serious graduating depends on this??!??

 

[Corey]

holy sh*t i would love for this to have been my senior project where the heck do you go to school? are you being serious graduating depends on this??!??

I go to Mountlake Terrace High School in Washington state. It doesn't depend on this exact project, its just something that I chose personally. The requirements are it must be in your interest of after school careers, and it must be 40 hours of labor.

 

[stephen12091985]

^^^yea i wish that was for us when i was a senior

 

[Corey]

Lol yeah, by the way, does l7 make a pipe that can be spark arrested?

 

[TheWalkingPlague]

fmf are good for stock but it looks like youare going to up it that is all im saying

 

[blasterdude14]

what you could do is buy a f7 header pipe and get an fmf powercore 2 silencer

 

[blasterman312]

Have you considered a Pro Circuit Exhaust?

Here is alittle taste

 

[blaster195]

So pretty much at my school we have this thing called a Culminating project that seniors do (12th graders) I for one am one of them. After much debating on either lifting my jeep 3.5" and putting 31" tires on it and modding the living sh*t out of my automatic wheelie machine (my blaster), I decided on my blaster! This all should run me if I'm lucky under $2,000 (this list does not include anything minor that I plan on doing such as brake changes, etc. you get the picture)

My plans for my senior project is as followed (keep in mind this is in order for me to graduate high school):
-Vito's 240 big bore kit
-FMF SST pipe with TurbineCore 2 Silencer
-+4" Extended swing arm
-Larger carb
-8 paddle haulers
-Block off and Remove my oil injection
-Banshee hubs
-Sand frame
-Prime frame
-Rattle can frame silver
-Remove airbox (DONE)
-Put on a k&n air filter (DONE)
-Re-jet properly (DONE)
-Custom fabricate air flow shrouds (DONE)

Any advice + tips will be greatly appreciated and very helpful, thanks a ton!

-Corey

I was going to do the same thing for senior project!!!!!

 

[calcium12]

no offence man....dont take this personally....but it seems kinda easy ?? like to me, taking apart my quad is kinda fun especially seeing the transformation...is this like a fun project ?