January 2014 ATV/BIKE-OTM Entries

[Awk08]

Gonna switch it up a little this month to see how it goes ?

ATV/Bike of the month.
ANY and ALL, ATV's, BIKE's, BUGGIE's, and even modified wheel barrows are welcome to enter
RUN WHAT YA BRUNG

for anyone entering a bike ect. feel free to switch details...... a-arms to forks ect.
or whatever else fits your ride in the entry form, just keep the details in the category they belong

Entries for ATV/BIKE Of The Month (January 2014) are now open!

Please make sure you have read the following thread before creating your entry.

Blaster Of The Month Entry Details, Rules and Requirements...​

Entries should be posted below by copy and pasting the completed modification form with your details.​

The modification form can be found here...
http://www.blasterforum.com/entries-botm-108/blaster-month-entry-details-rules-requirements-3275/#post31106st31106 ​

Only entrants for this months contest should post thier entries in here !​

Have a great time and GOOD LUCK!​

 

[Blaaster]

Before fitting the DMC Alien.

Year | Make | Model :

1. 2006
2. YFS 200
3. Blaster



Chassis | Suspension | Controls:
A Arms: Stock, with Diamond J 6inch widening and lowering kit.
swingarm: Stock.
Steering Stem: Stock.
Stabilizer: ??? 7 position
Axle : Banshee
Carrier: Stock.
Locknut: Stock.
Hubs F|R: Stock.
2 1/2" stud spacers all round.
Bars: Stock.
Throttle/Clutch Lever: Twister/Stock.
Grips: Stock.
Nerfs: Chinaman modified
Bumper: Stock.
Grab Bar: Stock.
Front Shocks: Dual rate YFZ450 Works
Rear Shock: Stock, with lowering thingy.
Brake Lines: Stock.
Rotors F|R: Stock.
Rims F|R: Stock.
Tires F|R: Kenda Klaw.

Body: Stock.
Frame: Stock.
Plastic: Stock, some removed.
Graphics|Seat Cover: Nil.
Number Backgrounds: Nil.
Handguards: Nil.
Bar Pad: Nil
Fuel Tank: Stock.

Engine|Drive System:
Cylinder|Head: W W Holden, 22cc Toroidial
Bore & Stroke: Stock.
Displacement: 195cc
Carburetor: 26mm Mukini, #320 main , needle on second lowest clip.
Air Filter|Box: Foam pod directly on carb throat.
Pipe|Silencer: DMC Alien
Clutch|Plates: Stock.
Gearing F|R: Stock.
CDI|Killswitch: Tether.
Cooling: Air.
Custom mods:...........Mild port and polish of exhaust port.
Pre mix ratio 25:1
2 stroke oil Castrol R30.

 

[boomadge]

Year | Make | Model :

1.1989
2.Honda
3.CR125R



Chassis | Suspension | Controls:
Forks: 43mm Showa conventional cartridge w/ 5w
swingarm: Stock
Steering Stem: +1 riser
Hubs F|R: stock
Bars: Fly midbend
Throttle/Clutch Lever: Motion pro
Grips: Pro Grip 801
Rear Shock: KYB (rebuilt,revalved,recharded for 160lb rider by works connection)
Brake Lines: New OEM
Rotors F|R: New OEM
Rims F|R: 21"stock/18"stock
Tires F|R: Dunlop/Dunlop

Body:
Frame: Fighting red custom powder coat
Plastic: OEM fighting red with HRC alum pro circuit stator cover
Graphics|Seat Cover: Oem honda
Number Backgrounds: HRC factory OEM
Handguards: none
Bar Pad: FLY
Fuel Tank: Stock 2 gallon/on off no res

Engine|Drive System:
Engine type: 2 Stroke, case reed, power valve
Cylinder|Head: Sleeved with wiseco/stock head (light port cleanup)
Bore & Stroke: stock 54 mm x 54 mm
Displacement: 124cc
Carburetor: Keihin PJ34
Air Filter|Box: UNI filter/stock box
Pipe|Silencer: Pro circuit (works)/Pro circuit factory 304
Clutch|Plates: Oem fibers/wiseco steel plates
Gearing F|R: 15 / 53
CDI|Killswitch: Stock/stock
Cooling: Liquid
Reeds:Boyesen

Custom Mods:
All custom color matched powder coating,forks/shocks reworked by works connection.
Wiseco steel clutch plates and vortex sprocket chain combo. Works connection frame guards where puchased from great britain as they could not be found to fit the 89 in the USA. All else new oem honda/hrc right down to the nuts and bolts.. About 400 hours of labor
Parts Proof can be found rf2comp_zpsbe102db8.jpg Photo by boomadge | Photobucket

 

[darrencurry08]

Year | Make | Model :

1. 2003
2. Yamaha
3. Blaster

Chassis | Suspension | Controls:

A Arms: Stock
swingarm: Stock
Steering Stem: Stock
Stabilizer: Stock
Axle : Stock
Carrier: Stock
Locknut: Stock
Hubs F|R: Stock
Bars: Stock
Throttle/Clutch Lever: Stock
Grips: Stock
Nerfs: Goldspeed
Bumper: Stock
Grab Bar: Stock
Front Shocks: Stock
Rear Shock: Stock
Brake Lines: Stock
Rotors F|R: Stock
Rims F|R: Stock
Tires F|R: Stock front/ 18-9.50-8 Rears

Body:

Frame: Stock
Plastic: Stock
Graphics|Seat Cover: Random Yamaha Flame Graphics /w Stock seat cover
Number Backgrounds: None
Handguards: None
Bar Pad: None
Fuel Tank: Stock

Engine|Drive System:

Cylinder|Head: Stock
Bore & Stroke: Bored but not sure on size
Displacement: Stock
Cam: Stock
Carburetor: Stock, #300 Main Jet
Air Filter|Box: Stock /w Air lid Removed
Pipe|Silencer: DMC Alien
Clutch|Plates: Stock
Gearing F|R: Stock
CDI|Killswitch: Stock
Cooling: Air

Custom mods:........... Mild Diy Porting, Boyeson Dual Stage Reeds, 32:1 Pre Mix,
2.5” Spacers All Round, QZR Heel Guards, Racing Ignition Coil, TORS Removed

 

[Durby]

MIKE "DURBY" OWENS

Built with love and pride for my kids:

http://www.blasterforum.com/full-rebuilds-128/durbys-blaster-rebuilds-monster-themes-kiddos-55198/

 

[Quadman1]

^^^^ can't go wrong there. Awesome looking quads that should be finished.

 

[Durby]

he took a lot of pride in building these bikes~ brandy