240 Top end and a couple carbs for sale

[Wifesblaster]

Selling my 240 top end with a pump fuel head and a race fuel head, v force 4 reeds, reed spacer, and upp intake for 35mm-38mm carb. Stock cylinder with 240 LA sleeve pressed in it. Cylinder is ported by Ken oconnor and it is a trail port.

Top end has roughly 6 hours on it and is in perfect shape. $450 shipped for the cylinder, piston, both heads, vf4's, reed spacer, and intake. This top end was on my +4 stroker bottom end.

Carbs for sale - 36mm PWK quad vent and 38mm PWK. $90 each shipped without pilot, main, or needle jet. $115 shipped with jets of your choice.

Text me if interested. 443-829-9144. Thanks

 

[bigd451]

Are you willing to sell the v force 4 reeds, reed spacer, and upp intake for 35mm-38mm carb separately?

 

[Wifesblaster]

I will sell separately if this whole package doesn't sell.

 

[bigd451]

Ok thanks, keep me posted.

 

[Wifesblaster]

Will do. Top end is still on the bike. If somebody is interested I will pull it off and take pictures.

 

[Herpderplol]

Wont let me message you? Says im not allowed to start a convo with you

 

[Wifesblaster]

Not sure why. Shoot me a text. My number is in original post.

 

[Wifesblaster]

The reason why I am selling my current top end is because I done believe it is capable to meet the demands of the custom dyno port pipe I had made. This cylinder ran good with off the shelf pipes. Woody's CT 240 motor seems to run pretty good so I am ordering the CT kit. Then it will be off to the blaster master for some doctoring.

 

[jus_me]

Wait, This whole time you had a sleeved 240? I always thought you had the Ct 240...


Anyhow. Is the 240 cyl ported for the +4 crank or was a spacer used? Knowing you I am sure it was ported the correct way but just trying to clarify. I would also be interested in the v force reeds and possibly one or both of the heads if you decide to split things up.

 

[Wifesblaster]

Was ported for the +4

 

[Wifesblaster]

38mm carb sold. 36mm carb is on hold. It is on hold because I made the buyer a deal. If he doesn't like the 38mm he can have the 36mm. I'm sure he will like it though. It was on the same setup as mine.

Thanks Mark. On its way out to ya tomorrow. Good talking to ya

 

[mlrblaster]

I can't wait to get it installed!!

 

[Wifesblaster]

I can't wait to get it installed!!

Did you get it dialed in yet? Last I talked to you it was close?

 

[Wifesblaster]

Both carbs are sold. Top end is still available

 

[mlrblaster]

Installed and idling beautifully. I have not been able to do a plug chop yet, my street is not long enough. I'll have to take it somewhere to do that. Thanks for the assistance in getting things situated. I'm amazed at how crisp the throttle is compared to the 34mm that was on it.

 

[Wifesblaster]

Installed and idling beautifully. I have not been able to do a plug chop yet, my street is not long enough. I'll have to take it somewhere to do that. Thanks for the assistance in getting things situated. I'm amazed at how crisp the throttle is compared to the 34mm that was on it.

Glad to hear you like it. Welcome to the 38mm family lol

 

[Wifesblaster]

Bump

 

[mlrblaster]

Glad to hear you like it. Welcome to the 38mm family lol

I looking forward to testing it out once I know the jetting is for sure correct. There is a race May 2nd that me and my buddies may be going to.

 

[Surrey blaster]

Was the pump fuel head done by Ken?

 

[JDCoon]

Interested in the top end kit. Could you post some pics or email them to me?