My blaster isnt fast enough???????????????????????????????????????????? ????? :-/ :-/

[DUALSTROKE]

Re: My blaster isnt fast enough???????????????????????????????????????????? ????? :-

tell me when you guys are done and ready to help me.....f*cking assholes lol.no but seriously stfu ok the bike is running a little rich but i kinda want to keep it on the rich side just to be safe cause i dont wanna burn the turbo up lol but really maybe a bigger carb and no i didnt do the porting a company did it for me believe its a dune port....another question anyone put a tach on their blasty if so how and how high can i rev it? thanks

Same thing I posted on page 1. A bigger carb,vf3's reed cage,3mm stroker crank,and the pipe will do ok for now but eventually sell the toomey and get an f7,power pro's trinity,etc. all are the same pipe just different peoples names on it. Also be careful how you use the stfu word.I know you are joking but that will get you nowhere around bf talking like that.Be positive,it was just a litle constructive criticism.lol good luck

 

[blasterfreek30]

Re: My blaster isnt fast enough???????????????????????????????????????????? ????? :-

ride like this and you will love your blaster YouTube - blaster wheelies

thats a flotek ported blasty right there

 

[yes se-r]

Re: My blaster isnt fast enough???????????????????????????????????????????? ????? :-

maybe get some nitrous ontop of your turbo set up?

 

[masterblaster81]

Re: My blaster isnt fast enough???????????????????????????????????????????? ????? :-

or you could just throw your blasty motor away and drop in a yz 400 in it like paulie b

 

[Outlawed Genetics]

Re: My blaster isnt fast enough???????????????????????????????????????????? ????? :-

personaly i dont even think its more upgrades that are needed atm. sounds like jetting is off or something. by the sounds of it maybe the needle. even a stock blaster doesnt take long to go through the gears like you described.

but if your needle is off that will make it run through the gears slow because its not giving all it has. the blaster i bought for parts was like that.... till i adjusted the needle. now it rips and i've yet to take any parts off of it lol

 

[Chevyssimpala]

Re: My blaster isnt fast enough???????????????????????????????????????????? ????? :-

it is rich but im not really sure how rich it is i kinda want to leave it a little on the rich side but not like it is now should i do plug chops and then go up one jet from were it is suppose to be ?

 

[Outlawed Genetics]

Re: My blaster isnt fast enough???????????????????????????????????????????? ????? :-

can you post a vid of you running it?

 

[Chevyssimpala]

Re: My blaster isnt fast enough???????????????????????????????????????????? ????? :-

no not today dont have a video camera

 

[burnin'_oil_2001]

Re: My blaster isnt fast enough???????????????????????????????????????????? ????? :-

most people think that their jetting is correct because they are using the correct main. their are many circuits to tune and they should be tuned from the bottom to the top. i would say that if you are not running at the minimum one size up on the pilot (if your pilot size is correct your air screw will be around 1 1/2-2 turns out) and richer on your needle clip (1 clip position down from stock) then you are too lean for your engine. below is a link to an article on jetting....it is long but it is worth the read.

http://www.blasterforum.com/engine-13/copy-how-jet-article-link-excellent-site-17371/

this can also be found in my signature. i hope that this helps.

 

[2strokepower]

Re: My blaster isnt fast enough???????????????????????????????????????????? ????? :-

cool video makes me want to rip sh*t up!

 

[4cfed]

Re: My blaster isnt fast enough???????????????????????????????????????????? ????? :-

thats a flotek ported blasty right there

and that blaster fkn rips!!!!!