Pressure test kit?

[RatchetMonkey]

Hi guys,

Ok so I've been looking through the forums to find a solution as to why my blaster has a high idle after its warmed up.

I noticed a few threads regarding pressure testing the head so i was just wondering where i can find a kit to test for leaks as i'm pretty sure i have one as it idles high when warm and i really don't want to fry the piston.

Any help would be appreciated.

Also I'm in the UK so shipping would need to be to the UK.

Thanks

 

[Awk08]

very simple to just build one yourself, just need to find a pressure gauge locally or online/ebay, then follow this thread to build and use it.........

http://www.blasterforum.com/do-yourself-20/build-use-leakdown-tester-10663/

 

[RatchetMonkey]

Cheers for the link bro,

Was just after buying a complete kit haha. I'm lazy when it comes to sourcing parts, mainly due to them being spread over several different shops over here in the UK :/

 

[Awk08]

Cheers for the link bro,

Was just after buying a complete kit haha. I'm lazy when it comes to sourcing parts, mainly due to them being spread over several different shops over here in the UK :/

couple clicks of the mouse and a guy in a postal uniform brings them right to your door, LOL

ebay.uk.....

low pressure gauge:
Low Pressure Gauge for fuel air oil or water 50mm 0/15 PSI & 0/1 Bar 1/4 BSPT D | eBay

fittings and hose:

Silicone Vacuum Vac Hose Pipe Tube 3mm 4mm 5mm 6mm 7mm 8mm 9mm 10mm All Silicon | eBay

Brass T Barbed Tee Fitting 1/4 Hose Air Water Fuel Boat | eBay

Bike Inner Tubes. 2 TUBES Tyre/Wheel Sizes 10 12 14 16 18 20 24 26 27 700c 28 | eBay

 

[Awk08]

Cheers for the link bro,

Was just after buying a complete kit haha. I'm lazy when it comes to sourcing parts, mainly due to them being spread over several different shops over here in the UK :/

couple clicks of the mouse and a guy in a postal uniform brings them right to your door, LOL

ebay.uk.....

low pressure gauge:
Low Pressure Gauge for fuel air oil or water 50mm 0/15 PSI & 0/1 Bar 1/4 BSPT D | eBay

a few possible fittings and hose:

Silicone Vacuum Vac Hose Pipe Tube 3mm 4mm 5mm 6mm 7mm 8mm 9mm 10mm All Silicon | eBay

Brass T Barbed Tee Fitting 1/4 Hose Air Water Fuel Boat | eBay

Bike Inner Tubes. 2 TUBES Tyre/Wheel Sizes 10 12 14 16 18 20 24 26 27 700c 28 | eBay

http://www.ebay.co.uk/itm/1-1-4X3-4...774?pt=LH_DefaultDomain_0&hash=item53ef777466

http://www.ebay.co.uk/itm/BRASS-BSP...aterials_Plumbing_MJ&var=&hash=item2c5f9aab46

http://www.ebay.co.uk/itm/Male-Elbo...aterials_Plumbing_MJ&var=&hash=item1c2f6f9898

http://www.ebay.co.uk/itm/BRASS-BSP...t=LH_DefaultDomain_3&var=&hash=item3cc003e906

http://www.ebay.co.uk/itm/BRASS-Mal...t=LH_DefaultDomain_3&var=&hash=item3a6c64ba15

 

[RatchetMonkey]

Cheers Squire,

Better get the purse out :/

 

[Herpderplol]

If your temperature is cold in the UK, as it is at my house, you turn up the idle a little to start cold, but once its warm, it runs high. My blaster runs pretty high after being warmed up because i need the idle high to keep it running as cold as it is.

 

[RatchetMonkey]

If your temperature is cold in the UK, as it is at my house, you turn up the idle a little to start cold, but once its warm, it runs high. My blaster runs pretty high after being warmed up because i need the idle high to keep it running as cold as it is.

My Carb has no adjustment screws

 

[Herpderplol]

My Carb has no adjustment screws

Do you have TORs system removed? if so, i doubt it was properly done since it doesnt have an idle screw...

 

[Blaaster]

My Carb has no adjustment screws

What sort of carb do you have that has no adjustments?

Not even an airscrew?