Is it time to laugh or cry?

[ruairiyblaster]

Chain snapped hit the casing and put a hole in it think I have a guy with A new one any tips when replacing it?

 

[Trinityblaster]

It is time to cry.lol

 

[Awk08]

it is time to cry, especially when 98% of chains jumping are preventable with maintainence/replacement when needed............

 

[ruairiyblaster]

Yup was completely my fault I knew the chain was loose still took it out now look just shows u shouldn't take shortcuts

 

[ruairiyblaster]

What case bond should I buy? I've got a flywheel puller and a torque wrench is that all the specialist tools ill need?

 

[Blaaster]

Do not do it by halves, have it TIG welded.

 

[ruairiyblaster]

Was going to order one of these

AUTOCARE INSTANT GASKET SEALER NON HARDENING/SHRINKING NO GASKET REQUIRED | eBay




GRANVILLE 40G CLEAR SILICONE INSTANT GASKET RTV | eBay

 

[Blaaster]

What case bond should I buy? I've got a flywheel puller and a torque wrench is that all the specialist tools ill need?

Ooops, I just woke up. Sorry.:-[

 

[Herpderplol]

Tips for this new one.... DONT BREAK THIS ONE!

 

[ruairiyblaster]

Right guys need some help can I split the left side case without taking the the clutch cover off ? I've got the bolts right round the left side of including the stator and flywheel should it just pull off now?

 

[jsanders347]

Take your lumps and laugh it off bud.

 

[Awk08]

Right guys need some help can I split the left side case without taking the the clutch cover off ? I've got the bolts right round the left side of including the stator and flywheel should it just pull off now?

yes, you can remove just that side, but you'll need a pulley/gear puller and long bolts that screw into 2 threaded holes under the stator, then it will push on the end of the crank and pull the case off.

a hammer is not on the list of tools needed for this.

puller looks like this........

 

[Awk08]

also...if that side crank bearing stays on the crank...it should be replaced, getting it off the crank and back into the case as it should be for reassembly, is likely to damage it

 

[ruairiyblaster]

Right so got my crank puller made up (ill email u a pic joe you will get a laugh from it!) bearing stayed in the case

Only question is how do I get the bearing out of my casing easily ?

 

[Awk08]

heat the case area around the bearing, not the bearing, with a propane torch, the bearing should drop right out
then freeze the bearing and heat the new case, it should drop right in.

but, you'll need a crank puller to pull the crank back thru the bearing in the new case
or.....

the KOR method:
http://www.blasterforum.com/engine-13/kor-engine-assembly-no-crank-puller-needed-51169/

i think it's in part 2, but watch from the beginning
(again....DO NOT USE A HAMMER !!!!!!)

what do they call homemade tools in ireland ???
we call them redneck

 

[Awk08]

Irish crank puller !!!!
looks like it worked good

 

[ruairiyblaster]

Thanks ill watch the videos 2moro it's 3 am with me now and I've just finished with the blaster I emailed you some pictures did u get them?

More updates to come

 

[ruairiyblaster]

Also thinking of putting a +3 vitos in with a spacer plate is there much gains with them?

 

[Awk08]

Also thinking of putting a +3 vitos in with a spacer plate is there much gains with them?

you'll gain some bottom end and lose a little top end

 

[ruairiyblaster]

You think it's worth the money if I have a perfect working crank anyway?